Zhejiang Zhongcun Precision Cutter Machinery Co., Ltd. is one of the most reliable manufacturers and suppliers of fiber cement board saw blade in China, featured by quality products and good service. Welcome to wholesale CE approved fiber cement board saw blade from our factory. Contact us for customized service and OEM service.
TITLE
Nakamura 305MM 16 Teeth fiber cement board saw blade
Features
1. PCD Tips for Abrasive Panel Cutting
The PCD cutting tips are suitable for fiber cement board, siding panels and cement-based composite boards, helping reduce rapid edge wear caused by abrasive materials.
2. Low Tooth Count with Large Chip Clearance
The low-tooth-count design and large gullet space help reduce cutting resistance and improve dust and chip evacuation during dry or semi-continuous cutting of fiber cement materials.
3. Stable Steel Body for Reduced Wobble
A tensioned and balanced steel body supports stable cutting performance, helping reduce edge chipping, blade wobble and inconsistent kerf quality.
4. Resharpenable Design for Lower Long-Term Cost
When cutting speed decreases, edge burrs increase or feeding resistance becomes obvious, the blade can be professionally resharpened according to actual edge wear, helping extend the service cycle of the PCD blade.
5. OEM and Project-Based Customization
Nakamura supports OEM marking, specification customization and bulk supply based on machine type, diameter, arbor size, tooth count, board thickness, cutting speed and packaging requirements.
Fiber Cement Tooling System
Cutting fiber cement board is not simply a matter of replacing one saw blade. Board density, thickness, machine speed and feeding method all affect blade life and cutting quality. Nakamura recommends buyers evaluate the PCD blade solution from the following four aspects:
| Evaluation Item | Key Points |
| Board Type | Fiber cement board, siding panel, backer board, cement-based composite panel |
| Machine Type | Handheld circular saw, table saw, panel saw or automatic cutting line |
| Working Frequency | Intermittent jobsite cutting, continuous factory cutting or distributor stock use |
| Maintenance Method | Resharpening requirement, cleaning process and spare blade planning |
PCD Resharpening Guide
After long-term cutting of abrasive panels, the cutting edge of a PCD blade will gradually become dull. Stop forcing the blade through the material and check whether resharpening is required when the following signs appear:
- Cutting resistance increases under the same feeding speed;
- More burrs, edge chipping or grey cutting marks appear on the panel edge;
- Machine load sound becomes heavier and cutting temperature increases;
- The PCD tip is not broken, but the edge becomes rounded or shows a visible wear land;
- Cutting efficiency drops below the normal working condition.
Resharpening suggestions:
- Clean resin, dust and cement particles before resharpening;
- Check whether the PCD tips have cracks, missing corners or brazing defects;
- Use a professional diamond grinding wheel to restore the cutting edge;
- Check runout, balance and tooth consistency after resharpening;
- Do not continue resharpening if the tips are severely broken or the steel body is deformed.
Maintenance Manual
To extend the service life of PCD saw blades, users are advised to follow these maintenance steps:
- Clean dust and attached particles after each use;
- Avoid contact with metal objects, nails or hard impurities;
- Store the blade in individual packaging or a protective sleeve when not in use;
- Regularly inspect the brazing area, steel body cracks and arbor wear;
- For continuous factory cutting, keep a record of blade usage, resharpening times and cutting materials.
Application
Suitable Materials:
- Fiber cement board
- Siding board
- Cement backer board
- Fiber-reinforced cement board
- Abrasive decorative building panels
- Factory panel cutting and jobsite installation cutting
Typical Users:
- Building panel processing factories
- Siding and façade installation contractors
- Tool distributors
- OEM brands
- Project buyers requiring stable long-term supply
Not Recommended For:
- Metal cutting
- Nail-embedded wood cutting
- Heavy stone cutting
- High-impact demolition work
Factory Show
Nakamura provides not only standard PCD saw blades, but also specification matching and batch production support for fiber cement cutting projects. According to customer requirements, our factory can support steel body processing, PCD tip brazing, tensioning, dynamic balancing, surface treatment, laser marking and OEM packaging.
For distributors and brand customers, we can develop a complete specification range, including different diameters, arbor sizes, tooth counts, kerf widths, packaging methods and private label solutions, helping customers build a complete Fiber Cement Tooling product line.
Hot Tags: fiber cement board saw blade, China fiber cement board saw blade manufacturers, suppliers, factory, 7 1 4 Fiber Cement Blade, 10T PCD Cutting Blade, 184mm Fiber Cement Board Blade, PCD Circular Saw Blade, 165mm PCD Circular Saw Blade, PCD Saw Blade For MDF